Configure EIGRP Class full basic toplogy


Task 1 :- Create topology given in pic

Task 2:- Configure IP Address according topology

 Task 3:- Configure loopback Address on both Router

Task 4 :- Configure EIGRP class full 

Task 5 :- Check Routing table 

Task 6 :- Check Both Router communication are Not ( ping both loopback )

-------------------------------------------------------------------------------------------------------------------


Task 2:- Configure IP Address according topology
Configure R1

R1#
R1#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
R1(config)#interface fastethernet 0/0
R1(config-if)#
R1(config-if)#ip address 192.168.12.1 255.255.255.0
R1(config-if)#
R1(config-if)#no shutdown
R1(config-if)#
*Mar  1 00:18:05.643: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar  1 00:18:06.643: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R1(config-if)#
R1(config-if)#exit
R1(config)#

Configure R2

R2#
R2#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
R2(config)#int fa 0/0
R2(config-if)#ip add 192.168.12.2 255.255.255.0
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#
R2(config)#
*Mar  1 00:02:51.195: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar  1 00:02:52.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R2(config)#exit

-------------------------------------------------------------------------------------------------------------------
 
Task 3:- Configure loopback Address on both Router

R1 configuration

R1(config)#
R1(config)#interface loopback 0
R1(config-if)#
*Mar  1 00:22:43.079: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up
R1(config-if)#
R1(config-if)#ip address 1.1.1.1 255.255.255.0
R1(config-if)#
R1(config-if)#no shutdown
R1(config-if)#exit 
R2 Configuration

R2#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
R2(config)#
R2(config)#interface loopback 0
R2(config-if)#
*Mar  1 00:19:11.979: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up
R2(config-if)#ip add 2.2.2.2 255.255.255.0
R2(config-if)#no sh
R2(config-if)#exit
R2(config)#
-----------------------------------------------------------------------------------------------------------------
  
Task 4 :- Configure EIGRP class full 

R1 Configuration 

R1(config)#
R1(config)#Router eigrp ?
  <1-65535>  Autonomous system number

R1(config)#Router eigrp 1
R1(config-router)#
R1(config-router)#network 192.168.12.0
R1(config-router)#network 1.1.1.0
R1(config-router)#exit
R1(config)#






R2 Configuration 


R2(config)#router eig
R2(config)#router eigrp 1
R2(config-router)#network 192.168.12.0
R2(config-router)#network 2.2.2.0
*Mar  1 00:21:59.071: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 1: Neighbor 192.168.12.1 (FastEthernet0/0) is up: new adjacency
R2(config-router)#exit------------------------------------------------------------------------------------------------------------------------


Task 5 :- Check Routing table 

R1 ROUTING TABLE

R1#show ip route eigrp
D    2.0.0.0/8 [90/409600] via 192.168.12.2, 00:02:28, FastEthernet0/0
R1#



R2 ROUTING TABLE


R2#
R2#show ip route eigrp
     1.0.0.0/24 is subnetted, 1 subnets
D       1.1.1.0 [90/409600] via 192.168.12.1, 00:01:14, FastEthernet0/0
     2.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
R2#

 
Task 6 :- Check Both Router communication are Not ( ping both loopback ) 


!! PING FROM R1 TO R2 LOOPBACK

R1#
R1#PING 2.2.2.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 16/31/44 ms
R1#

!! PING FROM R2 TO R1 LOOPBACK

R2#
R2#PING 1.1.1.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/36/60 ms
R2#