STEP 1 :- Configure Vlan 10 , 20 , 30 , 40 in Server switch.
STEP 2 :- Configure Server Switch port as Trunk
STEP 3 :- Configure 3 Client switch as Client mode
STEP 4 :- Now check Automatically Client will Access Vlan 10,20,30,40 from Server.



Sw1 :- (Server Switch )

Sw1#show vtp status
VTP Version : 2
Configuration Revision : 6
Maximum VLANs supported locally : 255
Number of existing VLANs : 8
VTP Operating Mode : Server
VTP Domain Name :
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x6F 0x13 0x88 0x18 0x69 0x04 0x00 0x85
Configuration last modified by 0.0.0.0 at 3-1-93 00:07:08
Local updater ID is 0.0.0.0 (no valid interface found)
Switch#


 Configure Vlan

Sw1>enable
Sw1#
Sw1#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Sw1(config)#
Sw1(config)#vlan 10
Sw1(config-vlan)#name IT
Sw1(config-vlan)#exit
Sw1(config)#vlan 20
Sw1(config-vlan)#name sales
Sw1(config-vlan)#exit
Sw1(config)#vlan 30
Sw1(config-vlan)#name HR
Sw1(config-vlan)#exit
Sw1(config)#swit
Sw1(config)#exit
Sw1#

Sw1(config)#vtp domain cisco
Changing VTP domain name from NULL to cisco
Sw1(config)#exit
Sw1#


Show Vlan


Sw1#show vlan

VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
10 IT active
20 sales active
30 HR active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup 

Now Create Trunk port fast 0/1,0/2,0/3 

Sw1(config)#
Sw1(config)#interface range fastEthernet 0/1 - 3
Sw1(config-if-range)#
Sw1(config-if-range)#switchport mode trunk 

Now Goto Client Switch Sw2 & Sw3 & Sw4

 
Sw2(config)#vtp mode client
Setting device to VTP CLIENT mode.
Sw2(config)#

Sw3(config)#vtp mode client
Setting device to VTP CLIENT mode.
Sw3(config)#

Sw4(config)#vtp mode client
Setting device to VTP CLIENT mode.
Sw4(config)#

Check Vlan on Sw2 & Sw3 & Sw4.


Sw2#show vlan

VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
Fa0/14, Fa0/15, Fa0/16, Fa0/17
Fa0/18, Fa0/19, Fa0/20, Fa0/21
Fa0/22, Fa0/23, Fa0/24
10 IT active
20 sales active
30 HR active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup


Same as Sw3 & Sw4