Task 1 :- Configure IP Address According topology.
Task 2 :- Configure loopback Address on R1,R2,R3.
Task 3 :- Configure RIP Default Route on R1,R2,R3
Task 4 :- Make sure R1 can reach R3
-----------------------------------------------------------------------------------------------------------------------------------
Task 1 :- Configure IP Address According topology.
R1 Configuration....
R1#
R1#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#
R1(config)#interface ethernet 0/0
R1(config-if)#
R1(config-if)#ip address 192.168.12.1 255.255.255.0
R1(config-if)#
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#int
*Apr 27 09:22:12.031: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
*Apr 27 09:22:13.037: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to up
R1(config)#
R1(config)#interface ethernet 0/1
R1(config-if)#
R1(config-if)#ip address 192.168.13.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#
*Apr 27 09:22:35.714: %LINK-3-UPDOWN: Interface Ethernet0/1, changed state to up
*Apr 27 09:22:36.720: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, changed state to up
R1(config)#
R2 Configuration...
R2#
R2#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#
R2(config)#interface ethernet 0/0
R2(config-if)#
R2(config-if)#ip address 192.168.12.2 255.255.255.0
R2(config-if)#
R2(config-if)#no shutdown
R2(config-if)#exit
*Apr 27 09:25:41.695: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
*Apr 27 09:25:42.700: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to upt
R2(config)#
R2(config)#interface serial 2/0
R2(config-if)#
R2(config-if)#ip address 192.168.23.2 255.255.255.0
R2(config-if)#
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#
R2(config)#
R2(config)#
*Apr 27 09:26:08.812: %LINK-3-UPDOWN: Interface Serial2/0, changed state to up
*Apr 27 09:26:09.813: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
R2(config)#
R3 Configuration...
R3#
R3#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
R3(config)#
R3(config)#interface ethernet 0/1
R3(config-if)#
R3(config-if)#ip address 192.168.13.3 255.255.255.0
R3(config-if)#
R3(config-if)#no shutdown
R3(config-if)#exit
*Apr 27 09:28:41.642: %LINK-3-UPDOWN: Interface Ethernet0/1, changed state to up
*Apr 27 09:28:42.651: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, changed state to up
R3(config)#interface serial 2/0
R3(config-if)#
R3(config-if)#ip address 192.168.23.2 255.255.255.0
R3(config-if)#
R3(config-if)#no shutdown
R3(config-if)#exit
R3(config)#
-----------------------------------------------------------------------------------------------------------------------------------
Task 2 :- Configure loopback Address on R1,R2,R3.
R1 configuration..
R1(config)#
R1(config)#interface loopback 1
R1(config-if)#
*Apr 27 09:32:17.301: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up
R1(config-if)#ip address 1.1.1.1 255.255.255.0
R1(config-if)#exit
R1(config)#
R2 configuration..
R2(config)#
R2(config)#interface loopback 1
R2(config-if)#
*Apr 27 09:32:32.545: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up
R2(config-if)#ip address 2.2.2.2 255.255.255.0
R2(config-if)#exit
R2(config)#
R3 configuration..
R3(config)#
R3(config)#interface loopback 1
R3(config-if)#
*Apr 27 09:32:32.545: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up
R3(config-if)#ip address 3.3.3.3 255.255.255.0
R3(config-if)#exit
R3(config)#
-----------------------------------------------------------------------------------------------------------------------------------
Task 3 :- Configure RIP Default Route on R1,R2,R3
R1 Configuration...
R1(config)#
R1(config)#
R1(config)#router rip
R1(config-router)#
R1(config-router)#network 0.0.0.0
R1(config-router)#
R1(config-router)#no auto-summary
R1(config-router)#
R1(config-router)#version 2
R1(config-router)#
R1(config-router)#
!! in The Default Route 0.0.0.0 in this command router Advertise all subnets of Router !!
R2 Configuration...
R2(config)#
R2(config)#
R2(config)#router rip
R2(config-router)#
R2(config-router)#network 0.0.0.0
R2(config-router)#
R2(config-router)#no auto-summary
R2(config-router)#
R2(config-router)#version 2
R2(config-router)#
R2(config-router)#
R3 Configuration...
R3(config)#
R3(config)#
R3(config)#router rip
R3(config-router)#
R3(config-router)#network 0.0.0.0
R3(config-router)#
R3(config-router)#no auto-summary
R3(config-router)#
R3(config-router)#version 2
R3(config-router)#
R3(config-router)#
-----------------------------------------------------------------------------------------------------------------------------------
Routing Table
R1
R1#show ip route rip
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
+ - replicated route, % - next hop override
Gateway of last resort is not set
2.0.0.0/24 is subnetted, 1 subnets
R 2.2.2.0 [120/1] via 192.168.12.2, 00:00:10, Ethernet0/0
3.0.0.0/24 is subnetted, 1 subnets
R 3.3.3.0 [120/1] via 192.168.13.3, 00:00:02, Ethernet0/1
R 192.168.23.0/24 [120/1] via 192.168.13.3, 00:00:02, Ethernet0/1
[120/1] via 192.168.12.2, 00:00:10, Ethernet0/0
R1#
Same As R2 and R3
-----------------------------------------------------------------------------------------------------------------------------------
Task 4 :- Make sure R1 can reach R3
ping R1 to R3 loopback
R1#
R1#ping 3.3.3.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 6/7/10 ms
R1#
R1#
R1#ping 2.2.2.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/9/12 ms
R1#
-----------------------------------------------------------------------------------------------------------------------------------
Social Plugin